Anet A6 - Prusa I3 Pro DIY kit

This is the best lubricating oil for your printer, to keep everything slide smoothly!

3D printing has never been easier, with this great adhesion spray! Just spray a little bit of 3DLAC directly onto the glass of your heated bed and start printing. The spray can even be used without heat for PLA and PETG, although we recommend heating the bed up to respectively 50 and 60 degrees as letting the glass cool down, will release your object automatically from the bed. 3DLAC comes in a handy 400ml spray can, which will last your for hundreds of prints.

While 3D printing using FDM, layers cool down after deposition an shrink. This shrinkage in turn cause layers below to be bend upwards, causing the familiar warping effect. In bad cases the print will come loose from the plate and will be ruined. But no more! 3DLAC will allow for great bonding of the printed plastic with the glass surface under it, allowing even large prints to be made without warping.

NOTE: Due to transport limitations this product is not available in all countries. Please login to check if your country is accepted.

3D printing has never been easier, with this great adhesion spray! Just spray a little bit of 3DLAC directly onto the glass of your heated bed and start printing. The spray can even be used without heat for PLA and PETG, although we recommend heating the bed up to respectively 50 and 60 degrees as letting the glass cool down, will release your object automatically from the bed. 3DLAC comes in a handy 400ml spray can, which will last your for hundreds of prints.

While 3D printing using FDM, layers cool down after deposition an shrink. This shrinkage in turn cause layers below to be bend upwards, causing the familiar warping effect. In bad cases the print will come loose from the plate and will be ruined. But no more! 3DLAC will allow for great bonding of the printed plastic with the glass surface under it, allowing even large prints to be made without warping.

NOTE: Due to transport limitations this product is not available in all countries. Please login to check if your country is accepted.

Using glass makes is easier to start your next print, because you can use clips to hold the glass to the heated bed. By just switching the glass plates you are ready for you next print. You can usea piece of kapton to stick a thermistor on top of the glass, for making accurate readings of the bed temperature.

This is Borosilicate glass which has little thermal expansion.

These clips can clamp up to 8mm, so enough for a glass plate and a thin sheet of aluminum.

MK8 nozzles are a bit shorter than the older MK7 version. You can use this nozzle with the following 3D printers:

• Prusa i3 met MK8 extruder
• Anet A6 3D-printer
• Wanhao 3D-printers
• MakerBot Replicator 2
• MakerBot Replicator 2x
• MakerBot 5th Generation

MK8 nozzles are a bit shorter than the older MK7 version. You can use this nozzle with the following 3D printers:

• Prusa i3 met MK8 extruder
• Anet A6 3D-printer
• Wanhao 3D-printers
• MakerBot Replicator 2
• MakerBot Replicator 2x
• MakerBot 5th Generation

MK8 nozzles are a bit shorter than the older MK7 version. You can use this nozzle with the following 3D printers:

• Prusa i3 met MK8 extruder
• Anet A6 3D-printer
• Wanhao 3D-printers
• MakerBot Replicator 2
• MakerBot Replicator 2x
• MakerBot 5th Generation

MK8 nozzles are a bit shorter than the older MK7 version. You can use this nozzle with the following 3D printers:

• Prusa i3 met MK8 extruder
• Anet A6 3D-printer
• Wanhao 3D-printers
• MakerBot Replicator 2
• MakerBot Replicator 2x
• MakerBot 5th Generation

Note that the stainless steel is very thin, so you should not put too much force onto the heat-break.

This product can also be used as spare part for our Anet A6 - Prusa i3 PRO DIY kit. It will work for all regular filaments like PLA, ABS and PETG.

This MK8 heaterblock Has a M6 screw-thread. The thermistor holes are already attached to the heaterblock. This heaterblock is compatible with most MK8 extruders and Prusa 3D printers.